Plastic Accessories

• Color
• Black

• Color Pattern
• Solid

• Density
• 1.2 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Shore D 70-80

• Heat Resistance
• Yes

• Leak Protection
• Other, Yes, Designed for Air-tight Installation

• Length
• Approx. 90 mm

• Material
• Engineering Plastic (High Strength)

• Melting Point
• 220-260C

• Plastic Molding Type
• Compression Molded

• Plastic Type
• Polyamide (PA6) or Polypropylene (PP)

• Shaping Mode
• Injection Molding

• Size
• Custom Fit for AHU Panel

• Surface Finish
• Matt/Glossy

• Tensile Strength
• 45 MPa

• Type
• Plastic Hinge for AHU (Air Handling Unit)

• UV Resistant
• Yes

• Weight
• Approx. 40 g

• Color
• White

• Color Pattern
• Solid

• Density
• 0.97 Gram per cubic centimeter(g/cm3)

• Hardness
• Rigid

• Heat Resistance
• Yes

• Leak Protection
• Other, Yes

• Length
• Approx. 6-10 cm

• Material
• Plastic

• Melting Point
• 120-130C (for PP/HDPE)

• Plastic Molding Type
• Injection Molded

• Plastic Type
• HDPE/PP

• Shaping Mode
• Injection Moulding

• Size
• Small/Compact

• Surface Finish
• Matte/Smooth

• Tensile Strength
• 20-30 MPa

• Type
• Plastic Pharma Container

• UV Resistant
• No

• Weight
• Approx. 10-20 g

• Color
• Grey

• Color Pattern
• Solid

• Density
• 1.2 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, High, suited for mechanical loads

• Heat Resistance
• Yes

• Length
• Customizable

• Material
• Engineering Plastic

• Melting Point
• 220C (approx., material dependent)

• Plastic Molding Type
• Precision Molded

• Plastic Type
• Nylon or Polyacetal

• Shaping Mode
• Injection Molding

• Size
• Standard and customizable

• Surface Finish
• Smooth, matte finish

• Tensile Strength
• 60-80 MPa

• Type
• Damper Gear

• UV Resistant
• Yes

• Weight
• Approx. 150-250g

• Color
• Black

• Color Pattern
• Solid Black

• Density
• 1.4 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Medium to High (per material grade)

• Heat Resistance
• Yes

• Leak Protection
• Other, Threaded seal, Leak-proof

• Length
• Customizable (Standard: 1 inch to 4 inch)

• Material
• High-Quality Plastic (likely PVC or Polypropylene)

• Melting Point
• PVC: 160C, Polypropylene: 130C

• Plastic Molding Type
• Thermoplastic Injection Molded

• Plastic Type
• PVC / Polypropylene (as per application)

• Shaping Mode
• Injection Molding

• Size
• Threaded - varies (commonly 1/2 inch, 3/4 inch, 1 inch, etc.)

• Surface Finish
• Smooth

• Tensile Strength
• Approximately 40 MPa (PVC)

• Type
• Plastic Elbow

• UV Resistant
• Yes (Outdoor grade available)

• Weight
• Lightweight (Approx. 10-30 grams depending on size)

• Color
• Off-White / Cream

• Color Pattern
• Solid, single color

• Density
• 1.4 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Medium to High (Shore D 70-85, typical for engineering plastics)

• Heat Resistance
• Yes

• Length
• Approx. 100 mm (diameter, estimated from image)

• Material
• Engineering Plastic (likely Nylon or Polyacetal)

• Melting Point
• 210C (Nylon typical value)

• Plastic Molding Type
• Precision Molded

• Plastic Type
• Nylon (Polyamide) / Delrin (Acetal)

• Shaping Mode
• Injection Molding

• Size
• Customizable or as per requirement

• Surface Finish
• Matte, slightly textured

• Tensile Strength
• 5500-8500 psi (Nylon typical)

• Type
• Plastic Sprocket

• UV Resistant
• Optional / Available on request

• Weight
• Lightweight (exact value varies by size and design)

• Color
• Grey

• Color Pattern
• Solid

• Density
• 1.2 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Medium

• Heat Resistance
• Yes

• Length
• Approx. 4-6 cm

• Material
• Plastic

• Melting Point
• Approx. 180C

• Plastic Molding Type
• Precision Molded

• Plastic Type
• Engineering Grade Plastic

• Shaping Mode
• Injection Molding

• Size
• Standard Fitment

• Surface Finish
• Matte

• Tensile Strength
• High

• Type
• Damper Parts

• UV Resistant
• Yes

• Weight
• Lightweight (Approx. 10-15 g)

• Color
• Black (standard)

• Color Pattern
• Solid

• Density
• 1.04 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Shore D 70 5

• Heat Resistance
• Yes

• Leak Protection
• Other, Seamless Fit for Leak Proof Operation

• Length
• 150 mm (customizable)

• Material
• High-Grade Plastic (Typically Polypropylene or ABS)

• Melting Point
• 210C (ABS)

• Plastic Molding Type
• Precision Injection Molding

• Plastic Type
• ABS/Polypropylene

• Shaping Mode
• Injection Molding

• Size
• Standard for AHU fittings (custom sizes available)

• Surface Finish
• Smooth & Glossy

• Tensile Strength
• ~45 MPa

• Type
• Plastic Coupler for AHU

• UV Resistant
• Yes, basic UV stabilizer added

• Weight
• About 90 grams

• Color
• Multicolor (Green, Red, Yellow, White)

• Color Pattern
• Colored Spots on Round Grid

• Density
• 1.15 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Medium

• Heat Resistance
• Yes

• Length
• Approx. 150 mm

• Material
• Plastic

• Melting Point
• Around 160C

• Plastic Molding Type
• Injection Molded

• Plastic Type
• UV-stabilized Polymeric Material

• Shaping Mode
• Injection Molding

• Size
• 150 mm Diameter

• Surface Finish
• Smooth with Patterned Openings

• Tensile Strength
• Moderate

• Type
• Round Plastic Bird Flight Diverter

• UV Resistant
• Yes

• Weight
• Lightweight (Around 100 grams)

• Color
• Grey (Custom Colors Available)

• Color Pattern
• Solid

• Density
• 1.1 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Shore D85 - D90

• Heat Resistance
• Yes

• Leak Protection
• Other, Yes (For Specified Applications)

• Length
• Customizable (Typically 10-200 mm)

• Material
• High Grade Engineering Plastic

• Melting Point
• Approx. 220C

• Plastic Molding Type
• Injection Molded

• Plastic Type
• ABS/Polycarbonate (as per requirement)

• Shaping Mode
• Injection Molding

• Size
• Standard/Customized Sizes

• Surface Finish
• Matte/Smooth

• Tensile Strength
• High (Depends on Material Type)

• Type
• Plastic Damper Parts

• UV Resistant
• Yes (Optional)

• Weight
• Lightweight (Approx. 10-200 gm/unit)

• Color
• Dark Grey

• Color Pattern
• Solid

• Density
• 1.04 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Medium to High (as per typical damper plate applications)

• Heat Resistance
• Yes

• Length
• Approx. 120 mm

• Material
• Plastic

• Melting Point
• 130C to 160C (depending on plastic grade)

• Plastic Molding Type
• Injection Molded

• Plastic Type
• ABS or Polypropylene (typical for damper plates)

• Shaping Mode
• Injection Molding

• Size
• 120 mm x 90 mm (approximate)

• Surface Finish
• Smooth with slight matte

• Tensile Strength
• 32-38 MPa

• Type
• Damper Plate

• UV Resistant
• Yes

• Weight
• Approx. 100 grams

• Color
• Black

• Color Pattern
• Solid Black

• Density
• 1.3 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, 65-75 Shore A (typical for elastomers)

• Heat Resistance
• Yes

• Leak Protection
• Other, Yes, for sealing applications

• Length
• Custom or As per Requirement

• Material
• Black Elastomer (likely Synthetic Rubber or Thermoplastic Elastomer)

• Melting Point
• 150C - 180C (dependent on specific elastomer)

• Plastic Molding Type
• Injection Molding

• Plastic Type
• Thermoplastic Elastomer (TPE) or Synthetic Rubber

• Shaping Mode
• Injection Molding

• Size
• Custom or As per Requirement

• Surface Finish
• Smooth

• Tensile Strength
• 10-20 MPa (typical range)

• Type
• Elastomer Part

• UV Resistant
• Yes (UV Stabilized options available)

• Weight
• Varies by Size

• Color
• Black

• Color Pattern
• Solid Black

• Density
• 1.2 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Standard Grade (as per application)

• Heat Resistance
• Yes

• Leak Protection
• Other, N/A (not applicable for bearing component)

• Length
• Customizable as per requirement

• Material
• High-grade Engineering Plastic

• Melting Point
• 160C - 220C

• Plastic Molding Type
• Injection Molded

• Plastic Type
• Reinforced Polymer

• Shaping Mode
• Injection Molding

• Size
• Varies (Custom size available)

• Surface Finish
• Smooth

• Tensile Strength
• High (varies by material selection)

• Type
• Plastic Traction Bearing

• UV Resistant
• Yes

• Weight
• Lightweight (Depends on size specification)

• Color
• Black

• Color Pattern
• Solid

• Density
• 1.3 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Shore D 70-80

• Heat Resistance
• Yes

• Leak Protection
• Other, Yes

• Length
• Approx. 50 mm

• Material
• High-Quality Plastic

• Melting Point
• 160-170C

• Plastic Molding Type
• Precision Molded

• Plastic Type
• Polypropylene / ABS

• Shaping Mode
• Injection Molding

• Size
• Customizable / Standard Inner Square (Approx. 40 mm)

• Surface Finish
• Smooth Matte

• Tensile Strength
• 25-35 MPa

• Type
• Plastic Support Bearing

• UV Resistant
• Yes

• Weight
• Approx. 35 g

• Color
• Black

• Color Pattern
• Solid

• Density
• 0.96 Gram per cubic centimeter(g/cm3)

• Hardness
• Rigid

• Heat Resistance
• Yes

• Leak Protection
• Other, Yes

• Length
• Customizable

• Material
• Plastic

• Melting Point
• ~130C (for HDPE)

• Plastic Molding Type
• Injection Molded

• Plastic Type
• High-Density Polyethylene (HDPE) / Polypropylene (PP)

• Shaping Mode
• Injection Molding

• Size
• Standard/Custom sizes available

• Surface Finish
• Matte / Textured

• Tensile Strength
• 18-30 MPa

• Type
• Fire Connector

• UV Resistant
• Yes

• Weight
• Lightweight (Exact weight varies by size)

• Color
• Black

• Color Pattern
• Solid

• Density
• 0.95 Gram per cubic centimeter(g/cm3)

• Hardness
• Rigid

• Heat Resistance
• Yes

• Leak Protection
• Other, Yes

• Length
• Standard (customizable as per requirement)

• Material
• Plastic

• Melting Point
• 130C - 135C

• Plastic Molding Type
• Thermoplastic

• Plastic Type
• High-Density Polyethylene (HDPE)

• Shaping Mode
• Injection Molding

• Size
• Available in variable sizes

• Surface Finish
• Smooth

• Tensile Strength
• 22 MPa

• Type
• Mid Joint Coupler

• UV Resistant
• Yes

• Weight
• Lightweight

• Color
• Grey (other colors available on request)

• Color Pattern
• Solid

• Density
• 1.41 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Shore D 60-80 (Depends on plastic type used)

• Heat Resistance
• Yes

• Leak Protection
• Other, Not applicable (perforated/open design for drainage)

• Length
• Custom, typically 300mm - 1500mm (as per specifications)

• Material
• Plastic (Polypropylene/Polyethylene/Acetal as typical options)

• Melting Point
• 130C - 175C (depending on plastic type)

• Plastic Molding Type
• Modular, Perforated Pattern

• Plastic Type
• Engineering Grade Plastic (Polypropylene/Acetal)

• Shaping Mode
• Injection Molding

• Size
• Customization available; standard width 50mm - 200mm

• Surface Finish
• Matte, Non-slip surface

• Tensile Strength
• Up to 45 MPa (depends on material selection)

• Type
• Modular Conveyor Clit

• UV Resistant
• Yes, UV stabilized materials available

• Weight
• Approx. 250g - 600g per clit (varies by size)

• Color
• Black

• Color Pattern
• Matte, Uniform Color

• Density
• 1.04 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Shore D 65-70

• Heat Resistance
• Yes

• Leak Protection
• Other, High Sealing Capability

• Length
• Standard 40 mm (customizable)

• Material
• High-grade Plastic Polymer

• Melting Point
• 110C - 140C

• Plastic Molding Type
• Precision Injection Molded

• Plastic Type
• ABS/Polypropylene

• Shaping Mode
• Injection Molding

• Size
• 25 mm x 40 mm x 40 mm (approx.)

• Surface Finish
• Smooth, Non-porous

• Tensile Strength
• 32 MPa

• Type
• Plastic AHU Parts

• UV Resistant
• Yes

• Weight
• Approx. 20 g each

• Color
• Multicolor (Green, Red, Yellow, White, Black)

• Color Pattern
• Color Marked with Reflective Accents

• Density
• 1.2 Gram per cubic centimeter(g/cm3)

• Hardness
• Rigid

• Heat Resistance
• Yes

• Length
• Approx. 12 cm

• Material
• Plastic

• Melting Point
• ~145C

• Plastic Molding Type
• Injection Molding

• Plastic Type
• Polycarbonate

• Shaping Mode
• Injection Molded

• Size
• Standard Square

• Surface Finish
• Smooth with Matte Zones

• Tensile Strength
• 900 kg/cm2

• Type
• Bird Flight Diverter

• UV Resistant
• Yes

• Weight
• Approx. 35 g

• Color
• Black

• Color Pattern
• Plain

• Density
• 1.20 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Medium/High

• Heat Resistance
• Yes

• Length
• Approx. 15 cm

• Material
• Plastic

• Melting Point
• 160-220C

• Plastic Molding Type
• Thermoplastic

• Plastic Type
• ABS/Polypropylene

• Shaping Mode
• Injection Molding

• Size
• Standard

• Surface Finish
• Matte

• Tensile Strength
• 40-50 MPa

• Type
• Door Handle

• UV Resistant
• Yes

• Weight
• 50-80 grams

• Color
• Red

• Color Pattern
• Solid

• Density
• 0.90 Gram per cubic centimeter(g/cm3)

• Hardness
• Rigid

• Heat Resistance
• Yes

• Length
• Approx. 10 cm

• Material
• Plastic

• Melting Point
• 160C - 170C

• Plastic Molding Type
• Molded

• Plastic Type
• Polypropylene (PP)

• Shaping Mode
• Injection Molding

• Size
• Standard

• Surface Finish
• Smooth

• Tensile Strength
• 30 MPa

• Type
• Plastic Cable Hanger

• UV Resistant
• Yes

• Weight
• Approx. 15 g

• Color
• Black

• Color Pattern
• Solid

• Density
• 0.97 Gram per cubic centimeter(g/cm3)

• Hardness
• Other, Shore D 65-75

• Heat Resistance
• Yes

• Leak Protection
• Other, Yes (Protects pallet corners from moisture ingress)

• Length
• Customizable; Commonly 100-200 mm

• Material
• High-Density Polyethylene (HDPE) / Engineering Plastic

• Melting Point
• ~130C (HDPE)

• Plastic Molding Type
• Injection Molded

• Plastic Type
• Industrial Grade Plastic

• Shaping Mode
• Injection Molding

• Size
• Standard & Custom Sizes

• Surface Finish
• Matte/Smooth

• Tensile Strength
• 20-30 MPa

• Type
• Plastic Skid Corner

• UV Resistant
• Yes

• Weight
• Approximately 150-400 grams (varies with size)

• Color
• Transparent

• Color Pattern
• Clear/Transparent

• Density
• 1.20 Gram per cubic centimeter(g/cm3)

• Hardness
• Rigid

• Heat Resistance
• Yes

• Leak Protection
• Other, Yes

• Length
• Approx. 4-10 cm (customizable)

• Material
• Polycarbonate (PC)

• Melting Point
• Approx. 230C

• Plastic Molding Type
• Injection Moulded

• Plastic Type
• Polycarbonate

• Shaping Mode
• Injection Molding

• Size
• Standard/custom sizes available

• Surface Finish
• Glossy/Smooth

• Tensile Strength
• 60 MPa (typical for PC)

• Type
• Plastic Cap

• UV Resistant
• Yes

• Weight
• Approx. 20-50 g (varies by size)